Most owners might want to set up or restore some drywall sooner or later of their homeowning life. It may be fairly intimidating, slicing into the “pores and skin” of your own home. However in the event you’re cautious and conscious of the essential concepts behind tips on how to set up drywall, it truly is fairly straightforward. We like the thought of beginning in an space like a kitchen backsplash as a result of, though you need to measure and reduce and set up with care to offer a flat workable vertical floor, the majority of your drywall work shall be coated up with a stunning backsplash. So it takes a little bit of the strain off, don’t you assume?

Repair Drywall for a Kitchen Backsplash

Right here’s a step-by-step information on putting in (or repairing) drywall, notably aimed toward doing it for a kitchen backsplash. (In fact, the overall tips are the identical just about anyplace, so this tutorial will aid you with most of your sheetrock-putting in wants.) Please observe that the photographs all through this text present totally different sections of the kitchen’s drywall, as a consequence of lighting and different photographic constraints.

Let’s start!

DIY Degree: Intermediate

Materials to repair a drywall for kitchen backsplash

Supplies Wanted: (not all proven in photograph)

  • drywall
  • razor blade
  • drywall screws and drill
  • putty knife / trowel
  • joint compound (also referred to as “drywall mud”)
  • drywall tape
  • sanding block – high-quality to medium
  • spray texture
  • primer& paint

Install drywall correctly

So as to have the ability to set up drywall appropriately, you’ll have to be sure that all of the vertical edges of the drywall itself may be screwed to a framing 2×four. Even when this implies slicing your sheetrock additional than you may want, or need, to chop it. The sting of the prevailing drywall within the photograph above ends proper on the fringe of a 2×four (which suggests one aspect of the drywall can be “floating” freely – not good), so we’ll want to chop it again to the subsequent framing stud.

remaining drywall and the new drywall piece

The pink line within the photograph above represents the place the two×four is. Discover we’ve got minimize midway over the two×four, so each the remaining drywall and the brand new drywall piece might be screwed securely to the two×four.

Razor Blade for Ddrywall

You might use a razor blade (field cutter, x-acto knife, no matter you name it) to get a clear reduce on the drywall.

cut the drywall corners clean

Use a field cutter to chop the drywall corners clear and sq..

Take out any screws or nails

Make certain the whole lot that might prohibit the brand new drywall from mendacity flat towards the framing studs is gone. Take out any screws or nails, if there are any. Additionally scrape away any residual gunk, together with glue or no matter else. The 2x4s ought to be free and clear.

cut the drywall at a halfway point

Within the occasion that you simply run into an area the place it’s unimaginable to chop the drywall at a midway level on a stud (corresponding to this area above the kitchen sink, for instance, the place the framing doesn’t match up with the cabinets), you’ll want to put in 2×four help.

After measuring the height

After measuring the peak of your area in addition to the space from that area to the closest framing stud, you’ll want to chop 2x4s in line with these measurements. On this occasion, that required an 18” 2×four (for the peak) and two 5” 2x4s (for the space from the closest 2×four).

Begin by screwing in the two shorter pieces

Start by screwing within the two shorter items to the closest framing stud. We used a diagonal screw course for attachment, two screws per piece.

Nail Gun for Drywall

Subsequent, you’ll want to connect your 2×four size to the 2 shorter items you simply put in. Use a nail gun when you have one, or screws, or good old style hammer-and-nails.

the new drywall to be secured on the sides

As you possibly can see from the photograph above, putting in this 2×four to the area will permit the brand new drywall to be secured on the edges. That is important for lengthy-time period help; if a drywall edge is left floating, it can bend and warp and probably crack…together with something that’s put in on prime of it (like backsplash tiles).

Drywall Install Step 9

Repeat this step in as many areas as you might want to guarantee 2×four framing help on the vertical axes of your new drywall.

Cut the new drywall pieces to your space

At this level, you’re able to measure, minimize, and suit your new drywall items to your area. Drywall sheets sometimes are available eight’ lengths (12’ lengths can be found as nicely however are far more troublesome to move and handle for the typical home-owner). Measure so that every drywall piece begins/ends on a stud, even when it means chopping a bit of size off an extended drywall piece and including in a second piece. However measure all partitions. The wall within the photograph above, with the pink line, measured eight’ ½” lengthy. Figuring out this, we have been capable of set up the adjoining drywall first, which took away ½” as a result of the brand new drywall is ½” thick. This made the purple line wall a precise eight’ lengthy – a lot simpler to work with.

Measure and pencil

Measure and pencil in your measurements on the drywall. Use a field cutter to attain the uncovered (non-brown) aspect of the sheetrock.

Carefully bend the sheetrock

Rigorously bend the sheetrock alongside the scored line.

Pull the sheetrock

Pull the sheetrock all the best way right down to separate the internal stuff.

Keeping the sheetrock bent

Protecting the sheetrock bent, you need to use a field cutter to chop via the again layer. Attempt to hold your cuts clear, however don’t fear in the event that they’re not good or if the paper backing rips a bit of bit. It shouldn’t have an effect on your set up.

measuring the sheetrock perimeter

Together with measuring the sheetrock perimeter, you’ll need to measure and reduce out areas for any electrical switches or retailers. Once more, measure, draw, and rating these areas.

Use a hammer to make it

Use a hammer or the again finish of a drywall knife to come out the middle and create a drywall gap.

A drywall knife is the easiest tool

A drywall knife is the simplest device to make use of right here for cleansing up your edges and corners.

Test-fit your drywall piece

Check-suit your drywall piece. Make certain all edges and corners lie flat and that any electrical issues are made precisely. If the drywall doesn’t lie flush, pull it off and use a drywall knife to “shave” the required edges till it does match.

close fit around electrical outlets

Goal for a reasonably shut match round electrical retailers and switches, though should you’re just a little off, it’s okay. Keep in mind that the electrical plate will cowl up just a little of the sting, so you will have a little bit of a security zone.

Corners are good here

Corners are good right here. In case your corners aren’t mendacity flat, double examine to ensure the previous drywall nook is minimize clear; it’s straightforward to miss an previous hunk of drywall within the corners, which retains the brand new piece from mendacity flush.

pull the drywall away from the wall

When all appears good, pull the drywall away from the wall simply a few inches so you possibly can mark the studs. This makes it a lot quicker and simpler to screw the drywall in as soon as it’s up there for good.

Screw in the new piece

Screw within the new piece of drywall alongside the studs that you simply’ve marked.

Measure carefully and cut carefully

Measure rigorously and minimize rigorously, and your drywall ought to go up pretty simply and shortly. If there are gaps between your drywall items however you’re planning on putting in a backsplash over them, you gained’t even want to fret about taping and mudding them.

drywall is screwed into place - mud and tape

When the drywall is screwed into place, it’s time to mud and tape. You’ll need some drywall tape, joint compound (also referred to as drywall mud), a superb to medium sanding block, a putty knife and bigger trowel, and gloves (elective).

Practice on a small piece of drywall

When you’ve by no means carried out this earlier than and have the choice, select a piece of drywall that’s considerably hidden to be your “follow” part. This specific part is behind the fridge.

spreading over the entire drywall

Start by spreading your joint compound over the cracks.

Fill the crack

The objective right here is to fill the crack sufficient to create a clean, seamless floor.

larger trowel-type spreader

You may as well use a bigger trowel-sort spreader for the mud. A bigger one similar to this helps to clean the mud extra cleanly.

Sand down latter

You need the joint compound to be thick sufficient to have the ability to sand down later, however not so thick that it takes perpetually to sand down later.

Cut a piece of drywall tape

Minimize a bit of drywall tape that’s lengthy sufficient to run alongside one seam, from one nook to a different.

Place the tape gently

Place the tape gently on the moist joint compound instantly over the seam.

Push the tape into the joint

Push the tape into the joint compound. You need all of the mesh to sink into the compound, creating a robust help when the compound dries.

put a little more wet compound

After the tape is pushed into the compound, put a bit extra moist compound onto your putty knife and run it over the tape once more.

Prepare to see this

Doing this may expose a few of the tape’s “grid” strains.

more compound so those grid lines

Add just a little extra compound so these grid strains are coated up, however add simply sufficient to cowl them (not an excessive amount of – you need layers to be as skinny as potential).

Let joint compound dry

Let joint compound dry. It make take some time – even 24 hours, relying on the thickness of the mud.

gently sand it smooth with a fine sanding block

When joint compound is totally dry, gently sand it clean with a advantageous sanding block.

Angle the block

Tip: Angle the block to taper the joint compound towards the wall in order to attenuate the potential of exposing the drywall tape.

If you notice irregularities

Should you discover irregularities, pockets, cracks, or if the drywall tape grid is uncovered, repeat the appliance steps with very skinny coats till the wall is clean and seamless.

This is a messy process

This can be a messy course of; be sure you vacuum your workspace as you go in order to keep away from monitoring the mud mud all over the place.

need to match the flat new drywall

In case your partitions are textured, you’ll have to match the flat new drywall to the remainder of your partitions by including comparable texture. To do that, start by taping off any close by surfaces that you simply DON’T need textured. This consists of counter tops, backsplashes, cupboards, and so on. Even electrical retailers and comparable ought to be coated.

Spray textures are available

Spray textures can be found at your native house enchancment retailer. These are two examples. I’ve discovered each to work equally properly.

Adjust the settings on your spray texture

Modify the settings in your spray texture as per the can’s directions, then apply spraying on a non-wall floor. When you have got the correct spray, you’re able to do the wall.

Make several light passes

Make a number of mild passes with the spray texture over the brand new drywall floor, protecting the spray can about two ft away out of your wall. (The tactic is just like spray portray – do fast, mild strokes. You possibly can all the time fill in additional later.) When your texture matches the encompassing partitions, cease spraying and let it dry.

Prime and paint the newly drywalled

Prime and paint the newly drywalled and textured wall. Congratulations in your seamless drywall set up!

Notice: The writer is an skilled, though not skilled, residence enchancment fanatic. Homedit is just not answerable for any accidents or damages triggered because of this tutorial.

  • Facebook
  • Google Plus